The process of adding a node to a 11.1 RAC is very similar to the 10.2 process described in Part 5 of this series. For this reason, this post will just focus on what has changed between the 2 versions. Here is the complete series up to now:

1. Installation of 10.2 And 11.1 Databases
2. Patches of 10.2 And 11.1 databases
3. Cloning Software and databases
4. Install a 10.2 RAC Database
5. Add a Node to a 10.2 RAC database
6. Remove a Node from a 10.2 RAC database
7. Install a 11.1 RAC Database
8. Add a Node to a 11.1 RAC database (This post!)
9. Remove a Node from a 11.1 RAC database
10. A ton of other stuff you should know

Before you start

Make sure you’ve kept a copy of the voting disk and that you have a backup of the OCR. Check that the locations for all the components to be installed, i.e.: Inventory, Clusterware, ASM, database software, OCR, Voting Disks, and data files, are writable. Confirm that all the prerequisites are met for the node and for the whole cluster with the node to be added.

Refer to the Oracle Clusterware Administration and Deployment Guide
11g Release 1 (11.1) - 4 Adding and Deleting Oracle Clusterware Homes
and the Oracle Real Application Clusters Administration and Deployment Guide
11g Release 1 (11.1) - 9 Adding and Deleting Oracle RAC from Nodes on Linux and UNIX Systems for the complete reference of how to perform these steps.

(more…)

This fifth post assumes that you want to add a new node to your cluster and database. It describes most of the associated “silent” syntaxes. Even if you don’t leverage RAC’s ability to add or remove nodes to gain in agility, it’s still very likely you’ll come to these techniques when you want to upgrade some of your Servers or Operating Systems. For a complete series agenda up to now, see below:

1. Installation of 10.2 And 11.1 Databases
2. Patches of 10.2 And 11.1 databases
3. Cloning Software and databases
4. Install a 10.2 RAC Database
5. Add a Node to a 10.2 RAC database (this post!)
6. Remove a Node from a 10.2 RAC database
7. Install a 11.1 RAC Database
8. Add a Node to a 11.1 RAC database
9. Remove a Node from a 11.1 RAC database
10. A ton of other stuff you should know

Adding a node involves adding all the components of the RAC in their order of appearance, i.e.: (1) The Clusterware and the associated resources, (2) the database software, (3) the listeners, (4) the ASM instance if necessary, and (5) the database instance. The last is the subject of this post.

For a complete reference to this procedure, see to the corresponding section of the 10.2 documentation.

Make Sure You Can Add The New Node To The Cluster

Before you start with anything else, proceed with the hardware and OS configuration. The new node must access the shared storage, the networks, the packages, parameter, users, etc. There is no difference if you add a node later or at the time of the initial install. You can use Oracle CVU and RDA as described in the corresponding section of the previous post to check that all the nodes can be part of a single cluster.

Adding a Node to the Clusterware

This step is actually pretty easy if the prerequisites are met. It’s also the one that can have the deepest impact on the cluster and the one that can end up badly. A lot of components are impacted by this addition: the voting disk, the cluster registry (OCR), and the inventories from all the nodes. Make sure you know how to revert any changes you are going to make. Make sure also that you have everything you need to revert the changes.

Note
Before you start with the node addition, make sure you’ve backed up the voting disk. There is no need to backup the OCR because it’s done automatically but it’s probably a good idea to locate the backup and make sure it contains the latest changes you’ve made.

You should also make sure that the Clusterware owner, oracle, or crs, or whatever it is, can write into the Clusterware ORACLE_HOME and the Oracle Inventory on the new server. Create the associated directory if necessary.

We’ll assume we want to add a new node rac-server5 to the cluster we’ve build in the previous post. In order to proceed, connect as the Clusterware owner on any of the existing nodes and run the set of commands below:

(more…)